Have you been hunting for information and facts around A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the job can move easily; if you have to open up a wall surface to remove the old tub and also place the new bathtub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to think about using one prior to you start. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bathtub in your restroom if you have already purchased a new tub as well as don't need to alter the plan of your previous supply of water pipes.
Your tools as well as product checklist ought to make up the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic because of the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub till the spirit level reads degree.
To mount faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Safeguard the faucet in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break an inflexible seal, creating the water to permeate the wall surface in between the bath and the tiling, resulting in difficulties with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very fascinated by Installing A Bathtub and I am assuming you enjoyed the new page. For those who appreciated our blog posting kindly don't forget to share it. Thanks for taking the time to read it.
Information